How To Shrink A Fitted Wool Baseball Hat?

It’s easy to shrink a fitted wool baseball hat. You just need to know how! Follow these simple steps and your hat will be as good as new.

Materials

You will need the following materials in order to shrink a fitted wool baseball hat: a pot, boiling water, a stove, a wooden spoon, a sink, cold water, and a towel.

Fitted wool baseball hat

What You’ll Need:
-a fitted wool baseball hat
-a bowl of boiling water
-a pot of boiling water
-towel
-iron
Instructions:
1. Fill a bowl with boiling water and place the hat in it, soaking for about five minutes. If your hat has a sweatband, make sure to soak that as well.
2. Fill a pot with boiling water and place it on the stove, letting it come to a boil.
3. After five minutes, remove the hat from the bowl of boiling water and place it on a towel. Use the towel to pat the hat dry, then place it on your head.
4. Dip the brim of the hat in the pot of boiling water for about 30 seconds, then remove it and place it back on your head.
5. Iron the wet brim of the hat with a hot iron, moving slowly around the circumference of the brim. Be careful not to burn yourself!
6. Let the hat cool on your head before removing it.

Scissors

-Gather your supplies: a wool baseball hat, a pair of sharp scissors, and a bowl of hot water.
-Wet the entire brim of the hat by dipping it in the hot water.
-Remove the wet hat and immediately begin cutting along the edge of the brim, working your way around the entire hat. Cut as close to the edge of the brim as possible.
-Once you have gone all the way around, dip the entire hat in the hot water again.
-Remove the hat and begin stretching it over your head. As you do this, the wool will shrink and the fit of the hat will become smaller.
-Continue stretching and shaping the hat until it is as small as you want it to be.
-Allow the hat to dry completely before wearing it.

Lighter

To shrink a fitted wool baseball hat, start by wetting the entire hat with warm water. Next, put the hat on and shape it to your head. then, put the hat in the dryer on a low heat setting and let it run for about 15 minutes. Finally, take the hat out of the dryer and check to see if it’s the right size. If it’s still too big, repeat the process until it shrinks to the appropriate size.

Steps

Wool baseball hats can shrank if they become too large, which is often the case when they are purchased online. The first step is to dampen the hat with water. Next, place the hat in the dryer on a low heat setting. Be sure to check the hat often to make sure it is not shrinking too much. Once the wool baseball hat has shrunk to the desired size, remove it from the dryer and allow it to air dry.

Put on the fitted wool baseball hat to check where you need to cut

1. Put on the fitted wool baseball hat to check where you need to cut. The hat should sit comfortably on your head without being too loose or too tight.
2. Make a note of where you need to cut the hat.
3. Remove the hat and lay it flat on a cutting surface.
4. Use a sharp pair of scissors to cut along the line you made in step 2.
5. Put the hat back on and enjoy your new, custom-fit baseball cap!

Cut along the edge of the hat, being careful not to cut too much off

Use sharp scissors to cut along the edge of the hat, being careful not to cut too much off. Next, wet the entire hat in lukewarm water. It’s important to use lukewarm water so you don’t damage the wool fibers. Gently squeeze out any excess water and then place the hat on a clean towel. Use your hands to shape the hat as it dries. Once it’s completely dry, try it on to make sure it fits properly. If it’s still too large, repeat the process.

Use the lighter to carefully singe the edge of the hat to prevent fraying

Gather your supplies. You will need a lighter, a small paintbrush, and an iron.

Use the lighter to carefully singe the edge of the hat to prevent fraying.

Turn the hat inside out and brush a layer of soot from the lighter onto the edge of the hat. Be sure to evenly coat the entire edge.

Place a piece of parchment paper over the sooty area and use the iron on low heat to set the soot. Allow the hat to cool completely before wearing.

Put the hat on and enjoy!

Before you shrink a hat, it’s important to understand that the process is irreversible. Once you’ve shrunk a wool hat, it can’t be un-shrunk. With that in mind, here are the steps you need to follow in order to shrink a fitted wool baseball hat:

1. Fill a pot with water and bring it to a boil.
2. Remove the pot from the heat and place the wool hat in the water.
3. Allow the hat to soak for about 15 minutes.
4. Remove the hat from the water and wring it out gently.
5. Place the wet hat on your head and shape it into its desired form.
6. Place the pot back on the stove and bring the water to a boil again.
7. Hold the shaped wool hat over the boiling water and allow it to steam for about 10 minutes.
8Remove the pot from the heat and allow the hat to cool before wearing it.